A. Aplastic anemia
B. Sickle cell anemia
C. Spherocytosis
D. Megaloblastic anemia
# Megaloblastic anemia is related to:
A. Folic acid and Vit. 12 deficiency
B. Iron deficiency
C. Vit. C deficiency
D. Vit. K deficiency
MCQs on Pathology of Blood Cells - General Pathology MCQs
A. Aplastic anemia
B. Sickle cell anemia
C. Spherocytosis
D. Megaloblastic anemia
# Megaloblastic anemia is related to:
A. Folic acid and Vit. 12 deficiency
B. Iron deficiency
C. Vit. C deficiency
D. Vit. K deficiency
A prepared cavity is best protected from moisture by:
# A prepared cavity is best protected from moisture by:
A. Cotton rolls
B. Saliva ejector
C. Rubber dam
D. Paper napkin
It is not possible to properly accomplish operative dentistry without control of mouth moisture. Moisture control refers to the exclusion of saliva, gingival sulcular fluid, and gingival bleeding from the operating field. It also involves preventing or limiting the spray from the handpiece and restorative debris from being swallowed or aspirated by the patient. he rubber dam, suction devices, and absorbents are variously effective in controlling moisture. Use of the rubber dam as an optimum means of gaining moisture control is recommended.
The finish line used in complete metal cast crown is:
# The finish line used in complete metal cast crown is:
A. Chamfer
B. Chamfer with bevel
C. Feather Edge
D. Shoulder
The correct answer is A. Chamfer.
Indications of Chamfer Finish Line
- Cast metal restorations
- Lingual aspect of metal ceramics
Advantages of Chamfer finish line:
- Conservative
- Good marginal adaptation
- Provides bulk
Disadvantages of Chamfer finish line:
- Improper fabrication may result in an unsupported tip
The best surface for a macrofilled composite resin is achieved by:
# The best surface for a macrofilled composite resin is achieved by:
A. Allowing polymerization to occur against a mylar matrix
B. Use of a green stone
C. Use of an extra fine silicone carbide disc
D. Use of a white stone
The correct answer is A. Allowing polymerization to occur against a mylar matrix.
Finishing of composite resins is best done after 24 hours during which time the polymerization is complete. However, if a subsequent appointment is not desired finishing procedures can be started 15 minutes after curing. The initial contouring can be done with a knife or diamond stone. The final finishing is done with rubber impregnated abrasives or rubber cup with polishing pastes or aluminium oxide disks. The best finish is obtained when the composite is allowed to set against a matrix or mylar strip.
Silicone differs from polyether polymer with respect to:
# Silicone differs from polyether polymer with respect to:
A. Affinity for water
B. Place and time of one
C. Area of one
D. Cost effectiveness
The correct answer is A. Affinity for water.
One of the disadvantages of the silicone impression materials (including condensation silicones) is their inherent hydrophobic nature. A nonionic surfactant can be added to the paste in the manufacturing process to render a degree of hydrophilicity to the surface of the material. This surfactant migrates toward the surface of the impression material and has its hydrophilic segment oriented toward the surface—a phenomenon that makes the surface more wettable by water. These impression materials still require a dry field for impression making. Pouring the set impression with a gypsum forming
mixture is facilitated because the wet stone has a greater affinity for the hydrophilic surface. The clinical significance of hydrophilic additives is discussed in subsequent sections.
One of the best agents used in successful pulp capping is:
# One of the best agents used in successful pulp capping is:
A. Copper cement
B. Calcium hydroxide
C. Amalgam
D. Zinc oxide
The correct answer is B. Calcium hydroxide.
Calcium hydroxide, because of its high pH value, acts as a pulp irritant and stimulates reparative dentine formation . It is also used as a pulp-capping agent, both in direct and indirect pulp capping.
The principal ingredient of an irreversible hydrocolloid impression is:
# The principal ingredient of an irreversible hydrocolloid impression is:
A. Agar
B. Tri sodium phosphate
C. Sodium alginate
D. Colloidal silica
The correct answer is C. Sodium alginate.
The chief active ingredient in the alginate impression materials is one of the soluble alginates, such as sodium, potassium, or triethanolamine alginate.
The diatomaceous earth acts as a filler to increase the strength and stiffness of the alginate gel. It also produces a smooth texture and ensures the formation of a firm gel surface that is not tacky.
Subscribe to:
Posts (Atom)